



High-performance repair product designed to seal head gasket and intake manifold gasket leaks. Its formula also helps seal cracks in cylinder heads and engine blocks while reducing coolant loss and the risk of overheating.
Secure payment - Information protected
Fast delivery - 90% within 2 to 3 days
Returns within 14 days
Rislone Head Seal is a high-performance repair product designed to seal head gasket and intake manifold gasket leaks. Its carbon-fiber-reinforced formula also helps seal cracks in cylinder heads and engine blocks while reducing coolant loss and the risk of overheating.
Repairs head gasket leaks: Helps seal leaks in head gaskets and intake manifold gaskets.
Seals cracks: Helps seal cracked or warped cylinder heads and engine blocks.
Reduces coolant loss: Helps reduce leaks in the cooling system.
Helps prevent overheating: Xtreme Cool technology helps reduce coolant temperature.
Antifreeze compatible: Suitable for various types of coolant, including OAT and HOAT formulations.
Easy to use: No cooling system flush is required when the system is clean and the product is used according to the manufacturer's instructions.
Rislone Head Seal is designed to address certain cooling system leaks, particularly in the following areas:
Head gaskets.
Intake manifold gaskets.
Cracked or warped cylinder heads.
Cracked engine blocks.
Plastic, cast iron, copper, or aluminum radiators.
Heater cores, freeze plugs, and other cooling system seals.
The product is suitable for gasoline and diesel engines, provided the engine can idle for 15 minutes without overheating or requiring additional coolant.
| Specification | Details |
|---|---|
| Brand | Rislone |
| Capacity | 1 L |
| Product type | Head gasket repair |
| Technology | Carbon-fiber-reinforced formula |
| Additional technology | Xtreme Cool |
| Compatibility | Antifreeze coolant and water |
| Engine types | Gasoline and diesel |
| Pre-treatment flushing | Not required if the system is clean and not significantly restricted |
Preparation: Allow the engine to cool completely. Shake the bottle vigorously before use.
Add the product: Remove the radiator cap, then pour in the appropriate amount of product according to the cooling system capacity.
Top up: Fill the radiator and expansion tank with the appropriate coolant, then close the system.
Circulation: Set the heater to maximum temperature and the fan to maximum speed. Run the engine until the thermostat opens or the engine reaches its normal operating temperature.
Cooling: Switch off the engine and allow it to cool before working on the cooling system again.
Final steps: Check the coolant level and top up if necessary. Then run the engine at approximately 1,200 rpm or drive gently for 15 minutes, before allowing the engine to cool.
The product should remain in the cooling system to provide continuous protection. Some leaks may be sealed quickly, while others may require several heating and cooling cycles.
Dosage:
Cooling systems from 5.5 to 9.49 L: Use half a bottle.
Cooling systems from 9.5 to 19 L: Use one full 1 L bottle.
Larger cooling systems: Use one bottle per 19 L of system capacity.
Precautions: Never open the cooling system when the engine is hot or under pressure. Protect the product from freezing. In cases of severe overheating or significant leaks, a mechanical diagnosis remains essential.
Reference: IRORP3000
Brand: Irontek
Renov'Phares is a renovation kit for the headlights of your vehicle, the kit allows the renovation of 2 headlights with one application in only 2 minutes. Renov'Phares is the easiest way to restore the radiance of your dulled headlights. After an application in about 2 minutes and a drying time close to 50 minutes, you can easily find your headlights as new.
Reference: WL10511
Brand: Wynn's
The MultiSERVE Particulate Filter Cleaning Kit allows professional cleaning of particulate filters through the application of the kit products with the Wynn's MultiSERVE machine. The kit removes solid deposits from clogged particulate filters, reduces exhaust pressure and improves engine performance. The kit contains: One cleaning product / 1 litre...
Reference: IT291
Brand: Irontek
Eco-cleaning is the economical solution to engine fouling problems. The use of this cleaner avoids the change of injectors and limits polluting emissions, we recommend this product to avoid the counter-visit when passing the technical inspection. In addition, this concentrated formula ensures unmatched performance. Also available for petrol engines:...
Reference: ERC1401F05FR
Reference: BAR1301
Brand: Bardahl
Bardahl Super Ethanol Injector CleanerSuper Ethanol Injector Cleaner is a 100% compatible and miscible formula E85. It prevents fouling and preserves the life of the engine while cleaning the injection system.This injector cleaner is compatible with all E85 super ethanol petrol engines originally equipped or equipped with an approved conversion box....